What can be wrong with my Motor Scooter? - scooter wheals ebay
My 150cc Motor Scooter released if the world. Straddling about 35, I stopped going. The engine starts and stops again, and speed than normal, but maybe not. Ideas? I would do the job itself, as the repair is not cheap.
Scooter Wheals Ebay What Can Be Wrong With My Motor Scooter?
7 comments:
Chain breaks or is worn or clutch gearbox is stripped in trouble or drive pinion
Belt is gone.
This is the easy way to replace it.
http://www.myvento.net/index.php?option = ...
To remove the tape.
First you should have two strong hands, and be careful
Be sure to push the kick starter shaft pull the cover, the tree remains in the engine, it will prevent the spring to kick in and fix a new problem.
Paul aka Sporty
# 1 "First remove the cover while the spring kick start tree used for taking a kick, kick starter shaft remains in the engine.
# 2-Remove the rear disc halves, the maximum width with both hands.
# 3 - now hold the roll with your right hand and left hand to get the belt on the underside of the rear part.
# 4 - well, the upper end of the strip, it can break you at the top of the car outside of the pulley and pulling the pulley and rotate the rear.
# 5 - If you are going to be a fan blade connected with the belt away from the belt by turning the rear wheel drive pulley and belt.
To install the belt.
Put the belt so that the text box can be read on his belt.
To buy # 1 - Getting the belt on the back of the disc to be removed by using step # 2 on the belt.
# 2 - Remove the tape and a hook on the fan blade on the disc with a belt.
# 3-If you back a leaf blower on the drive with the seat belt just walk the belt by the rotation of the pulley and tighten the strap attached.
# 4 - Replace the lid of the drive unit to play in the tree and all the way to drop it.
I made it for 5 years.
Sounds like the belt CVT is completely broken. This is a difficult solution, remove the side panel and the film, which was written by the size anywhere. Get a replacement, and waiting, you get to give change to ... not hard to do if you know how, if not almost impossible Dang! :)
Sounds like the belt CVT is completely broken. This is a difficult solution, remove the side panel and the film, which was written by the size anywhere. Get a replacement, and waiting, you get to give change to ... not hard to do if you know how, if not almost impossible Dang! :)
Yes, sounds like the band broke up. Malossi Kevlar belt leads for most models. The people I know who ride on the new switch to them for what is not broken again.
Hey, sounds like the belt broke. This is long, usually under the hood, if you have a kickstart, that coverage will leave a kickstart. On a bike, as my son is attached Suzuki Katana SC, the rear wheel to the other side of the deck that I mean the deck is connected.
If it is a default configuration, you can buy a new belt, take the kickstart and remove the screws on the lid - usually head Allen screws. When in cover, do not break the paper seal or just a new band with the case - which are really cheap.
Once you have coverage, you can immediately see if the tape breaks. Remove the old belt and other residues (there are usually a couple of flakes and debris from the old rubber band and can block the mechanism of initiation or start-up agreement if they are left there) and the establishment of a belt.
You should see 2-wheeler from there, small and large. Insert the new band on the premiere, making sure that it is right in the slot, you will see. Then put the tape on the small - Do you like it too narrowly on, even if only most of the tape, and turn the big wheel in the opposite direction, it will move to the belt on the sprockets. A bit like being back in a bicycle chain according to the narrowest.
Then put the seal and lid (in the thread too tight or not) pull the strings, and it is good to go. It is a relatively simple task to take longer than one hour if everything was as planned. Good luck:)
Your bike is probably a transmission-type CVT with a belt, I suspect that your belt broke that. You must remove the big plug on the left side of the engine / tranny access to the tape.
Post a Comment